PROJECTION PLANNING · 7 MIN READ
Projector throw ratio: a practical guide.
Work from image width and projection distance, then check the lens against the real installation.
By ezav · Published 20 October 2026
Choosing a projector lens starts with two measurements: the width of the projected image and the available projection distance. Throw ratio connects them. It helps establish whether a projector and lens can produce the required image from the proposed mounting position.
A matching ratio is only the first check. Compatibility, focus range, lens shift and physical installation space must also work.
What is projector throw ratio?
Throw ratio is the projection distance divided by the projected image width. For preliminary planning, use:
Throw ratio ≈ projection distance ÷ image width
A 4-metre-wide image projected from approximately 6 metres away requires a nominal ratio of 6 ÷ 4 = 1.5:1. Use the same units for distance and width.
Use image width, not diagonal or height. Work from the full projected image footprint; if content occupies only part of the projector’s raster, distinguish that active content area from the full optical image.
The ratio is a planning relationship, not a substitute for the manufacturer’s model-specific distance formula. Some formulas include an additional offset and published tolerances. [2]
How to calculate projection distance
Projection distance ≈ image width × throw ratio
For a 5-metre-wide image:
| Throw ratio | Approximate distance |
|---|---|
| 0.8:1 | 4 m |
| 1.2:1 | 6 m |
| 1.5:1 | 7.5 m |
| 2.0:1 | 10 m |
These are preliminary distances for a flat image plane with conventional alignment. Confirm the exact projector, lens, image size and measurement reference before finalising the mounting position.
How to calculate image width
Image width ≈ projection distance ÷ throw ratio
At a distance of 8 metres, a 1.6:1 lens setting produces an image approximately 8 ÷ 1.6 = 5 metres wide.
For a 16:9 image, the corresponding height is 5 × 9 ÷ 16 ≈ 2.81 metres. Aspect ratio determines the relationship between width and height; the throw-ratio calculation still uses width.
What does a zoom-lens range mean?
A lens specified as 1.2–1.8:1 varies its throw ratio within that range using optical zoom. For a 4-metre-wide image, the nominal distance range is 4.8–7.2 metres.
A proposed distance of 6 metres requires 1.5:1 and falls inside that range. A distance of 8 metres requires 2.0:1 and falls outside it.
Where practical, leave adjustment room instead of designing exactly at a published limit. Apply the manufacturer’s stated tolerances; do not assume a universal margin.
A practical lens-selection example
Consider an exhibition with a 6-metre-wide image, a 7.5-metre projection distance and a flat projection surface. The nominal required ratio is:
7.5 ÷ 6 = 1.25:1
An illustrative 1.1–1.5:1 zoom lens includes this ratio. An illustrative 1.5–2.0:1 lens does not. These ranges demonstrate the selection process; they are not equipment recommendations.
Before approving the candidate lens, check:
- Compatibility: the exact lens must be approved for the selected projector. Published ratios can depend on the projector used. [1]
- Focus and image size: confirm the supported projection distance and image-size range.
- Lens shift: verify that the image can reach its intended position from the proposed mounting height and lateral position.
- Physical space: allow for the projector body, connectors, ventilation, mounting and maintenance access.
- Beam clearance: check for visitors, structures, fixtures and other equipment that could obstruct the optical path.
Where should projection distance be measured?
Use the reference point shown in the manufacturer’s installation drawing. A dimension to a bracket, rear wall or projector casing is not automatically the published projection distance.
For example, Christie’s DHD635-GS technical reference measures throw distance from the centre of the projector’s front foot and includes offsets in its distance formulas. Those conventions apply to that documented model, not every projector. [2]
For folded and ultra-short-throw optics, check the installation drawing especially carefully. The casing-to-wall gap may not be the distance used in the formula.
Throw ratio, lens shift and keystone: the difference
| Term | What it controls |
|---|---|
| Throw ratio | The relationship between image width and projection distance. |
| Optical zoom | Image size within the supported lens range. |
| Lens shift | Image position without needing to tilt the projector. |
| Keystone correction | Digital correction of trapezoidal image distortion. |
Lens shift can help when the projector cannot sit directly in front of the image, but available movement depends on the model and operating position. Do not assume that maximum horizontal and vertical shift are available simultaneously; check the shift diagram. [3]
Digital correction does not expand the lens’s optical throw range. It can reduce the usable image area and effective resolution, so establish optical placement before relying on image processing.
What changes with multiple projectors?
For edge blending, use each projector’s full projected image width, including its overlap area.
Suppose two equal images cover a 10-metre-wide surface with 1 metre of shared overlap. If each image is W metres wide:
2W − 1 = 10 → W = 5.5 m
Each projector covers 5.5 metres, not 5 metres. At a distance of 6.6 metres, the nominal ratio is 6.6 ÷ 5.5 = 1.2:1.
This example assumes equal images on one flat plane. Curved surfaces, angled projection and irregular mapping surfaces require more detailed geometry and focus checks.
Common mistakes to avoid
- Using screen diagonal instead of projected image width.
- Measuring distance from the wrong reference point.
- Selecting a lens without confirming projector compatibility.
- Ignoring focus limits, shift limits or supported image size.
- Forgetting overlap in a multi-projector layout.
- Assuming a correct throw ratio guarantees sufficient brightness.
Throw ratio establishes whether the image can fit. Brightness, contrast, resolution and content legibility need separate checks.
Resources and references
- Christie — lens specifications and projector compatibility
An example of manufacturer documentation listing a lens’s throw range, compatible projectors and guidance to consult specific distance formulas. Included as a documentation example, not a product recommendation.
- Christie — DHD635-GS lens throw ratios (PDF)
A model-specific reference illustrating measurement points, formula offsets and tolerances. An archived technical example, not universal installation guidance.
- Epson — adjusting the image position using lens shift
Manufacturer guidance on lens-shift operation. The illustrated limits apply to the models covered by that manual.
References checked 20 October 2026. For an actual installation, consult the latest documentation for the exact projector and lens combination being supplied.